How to install a hunter sprinkler head?
An advantage of having an irrigation sprinkler system is the automated irrigation of your property. Depending on the season, sprinkler systems reduce the need to lug a hose around the yard to water the garden nearly every day. Sprinkler heads are only a tiny part of a more extensive system that could be broken due to repair. In the following section, let’s see how to install, adjust and replace Hunter sprinkler heads.
You can place a directed flush cap on Hunter spray bodies to flush debris out of the line during the first installation or service. Here are the steps to install the Hunter sprinkler head.
- Place flush caps in the vicinity of the plants, and then run the irrigation system to flush the lines.
- Raise the riser using the ring to remove the flush cap by rotating the cap counterclockwise.
- Install the nozzle by tightening it with a clockwise turn. After the nozzles are pulled, the two-piece ratcheting risers on the PS Ultra and Pro-Spray allow you to rotate the riser in either way to align it.
You may contact sprinkler repair services for hunter head sprinkler installation.
How to adjust hunter sprinkler head?
You can alter the Sprinklers with or without water. One should also do Hunter sprinkler head adjustment before installation.
Below are steps taken to adjust a hunter sprinkler head:
- The default position of adjustable heads is around 180°. You may adjust a Hunter rotor head with water on or off. One can make the best Basic adjustments before the installation.
- To finish any stopped rotation cycle, turn the nozzle turret counterclockwise to the left and stop using the palm of your hand.
- Turn the nozzle turret to the right and stop in a clockwise direction. That is the arc’s fixed side. To alter the arc, keep the nozzle turret in this position. The proper halt remains constant.
To widen the arc
- Put the Hunter wrench’s plastic essential end—which may be purchased here—into the rotor head’s adjustment socket.
- Turn the wrench clockwise while holding the nozzle turret at the right stop. The arc will rise by 90° for each complete 360° spin of the twist.
- You may adjust any arc between 40° and 360°.
- When the wrench reaches the maximum arc of 360° (full circle), it will stop rotating or make a ratcheting sound.
Reduce the arc by:
- Put the Hunter wrench’s plastic key end into the adjustment socket.
- Turn the wrench counterclockwise while maintaining the nozzle turret’s position at the right stop. The arc will be reduced by 90° for each complete 360° spin of the wrench.
- You may adjust any arc between 40° and 360°.
- When the minimum arc of 40° has been reached, the wrench will cease rotating or make a ratcheting sound.
To alter the hunter pop-up sprinkler head radius:
The Hunter Key’s steel hex end should be inserted into the radius adjustment screw. Then you may adjust the radius by turning either counterclockwise or clockwise (into the water stream). You can remove up to 25% of the radius.
How to Replace Hunter Sprinkler Head?
This section will see how to replace the hunter sprinkler head. Regardless of how the hunter sprinkler head is broken or stopped operating. You can follow the steps below for hunter sprinkler heads replacement by yourself or call the irrigation provider to replace the hunter sprinkler head.
Take out the damaged head:
- Place a plastic sheet adjacent to the damaged sprinkler head on the ground.
- Carve an 8-inch circle around the old head using a garden spade.
- Grab the sod by the roots and discard it.
- Dig around the old head and place the soil on the poly sheet.
- Unscrew the broken head after you’ve reached the water line.
- The likelihood that the hole will fill with water and dirt will enter the water line increases if the head is situated in a low area in a watering zone. Utilize your shop vacuum to remove the muck. (The water line is later flushed.)
Select the new head height:
- Remove the old riser fitting and screw it onto the new head if it is removed with the previous head.
- Screw the new head into the water line to test its fit. The top of the skull shouldn’t protrude into the grass; it should be flat with the ground.
- If it’s not the perfect height, pick up a brand-new poly cutoff riser with many threaded parts (about $1 each at home stores), and cut it to the necessary length.
Several trials (and risers) might be necessary to find the ideal height. When you’ve reached the perfect height, remove the head and flush the line by following these instructions.
Create a tool for flushing and flushing the water line:
No matter how careful you are, dirt will inevitably get into the fitting for the water line. You’ll need to wash it if your shop vacuum cannot eliminate all the earth with 3/4-in. PVC pipe and the fittings (around $5 in parts at home stores) construct a flushing tool. After that, run the water line (Photo 3). Suck the water out of the flushing tool to complete.
Head and backfill installation:
Backfill the hole after screwing the new head into the water line that has been flushed. As you tamp the earth with your hand, position the head, so it rests squarely in the hole. Replace the grass to complete the task. Water the grassroots immediately to re-establish.
Can you replace Rainbird Sprinkler’s head with Hunter Sprinkler Head?
Rainbird sprinkler head:
Rainbird sprinkler heads are small and dependable for any application. They have these below features:
- A tiny exposed cover practically conceals the unit for more beautiful landscapes.
- Made with corrosion-resistant materials, such as stainless steel, ensuring long product life even under high pressure or surge.
- When the wiper retracts, a pressure-activated seal prevents debris from entering and minimizes water waste.
Are hunter and rainbird sprinkler heads interchangeable?
You do not need a different brand of sprinkler head to replace the broken one. A Pop-up or impact are permissible, but only if they are of the same kind (rotor- or gear-d0riven). The replacement head must thus have a comparable inches-per-hour (iph) or gallons-per-minute (GPM) delivery rate to the previous one.
Hunter vs Rainbird sprinkler heads:
Hunter items are more robust than those made by Rainbird. They can withstand higher PSIs, which is crucial for winterization, water pressure, and adverse weather. Sprinkler heads are buried in the earth and exposed to high temperatures.
How Johnny’s Turf can help you?
Sprinkler issues can frequently pose a threat to your complete irrigation system. They might, however, sustain harm over time or from excessive development. In such circumstances, you should seek the help of a professional sprinkler repair, Jacksonville, for servicing.
We provide comprehensive lawn sprinkler repair in Jacksonville to repair your broken sprinklers and update them to cover a larger area. Our skilled and knowledgeable workers can fix any damaged part of your sprinkler, including broken pipes, lawn sprinkler valves, and electrical problems.
Our staff offers lawn sprinkler repair in Jacksonville after thoroughly evaluating the entire scenario. We provide services to solve any problem you may be having with your sprinklers.
